Worksurface

Effective ESD Control in a Service or Repair Center

Image scsstaticcontrol September 21, 2018 0

The best-equipped service bench in your shop can be a real money-maker when set up properly. It can also be a source of frustration and lost revenue if the threat of ElectroStatic Discharge (ESD) is ignored.

A typical scenario might be where an electronic product is brought in for service, properly diagnosed and repaired, only to find a new symptom requiring additional repair. Unless the technician understands the ESD problem and has developed methods to keep it in check damage from static electricity cannot be ruled out as a potential source of the new problem.

Static electricity is nothing new; it’s all around us and always has been. What has changed is the spread of semiconductors in almost every consumer product we buy. As device complexity increases, often its static sensitivity increases as well. Some semiconductor devices may be damaged by as little as 20-30 volts!

It is important to note that this post is addressing the issue of ESD in terms of control, and not elimination. The potential for an ESD event to occur cannot be completely eliminated outside of a laboratory environment, but we can greatly reduce the risk with proper training and equipment. By implementing a good static control program and developing some simple habits, ESD can be effectively controlled.

The Source of the Problem

Static is all around us. We occasionally will see or feel it by walking on carpet, touching something or someone and feeling the “zap” of a static discharge. The perception level varies but static charge is typically 2000-3000 volts before we can feel it. ESD sensitivity of some parts is under 100 volts – well below the level that we would be able to detect.

Even though carpet may not be used around the service bench, there are many other static “generators” may not be obvious and frequently found around or on a service bench. The innocent-looking Styrofoam coffee cup can be a tremendous source of static. The simple act of pulling several inches of adhesive tape from a roll can generate several thousand volts of static! Many insulative materials will develop a charge by rubbing them or separating them from another material. This phenomenon is known as “tribocharging” and it occurs often where there are insulative materials present.

*Sources of Charge Generation: Unwinding a Roll of Tape*

People are often a major factor in generation of static charges. Studies have shown that personnel in a manufacturing environment frequently develop 5000 volts or more just by walking across the floor. Again, this is “tribocharging” produced by the separation of their shoes and the flooring as they walk.

A technician seated at a non-ESD workbench could easily have a 400-500 volt charge on his or her body caused not only by friction or tribocharging, but additionally by the constant change in body capacitance that occurs from natural movements. The simple act of lifting both feet off the floor can raise the measured voltage on a person as much as 500-1000 volts.

Setting up a “Static Safe” Program

Perhaps the most important factor in a successful static control program is developing an awareness of the “unseen” problem. One of the best ways to demonstrate the ESD hazard is by using a “static field meter”. The visual impact of locating and measuring static charges of more than 1000 volts will get the attention of skeptical individuals.

*Static Field Meter – find more information here*

Education of Personnel

ESD education and awareness are essential basic ingredients in any effective static control program. A high level of static awareness must be created and maintained in and around the protected area. Once personnel understand the potential problem, reinforce the understanding by hanging up static control posters in strategic locations. The technician doesn’t need an unaware and/or unprotected person wandering over and touching things on the service bench.

Workstation Grounding

To minimize the threat of an ESD event, we need to bring all components of the system to the same relative potential and maintain that potential. Workstations can be grounded with the following options:

Establish an ESD Common Grounding Point, an electrical junction where all ESD grounds are connected to. Usually, a common ground point is connected to ground, preferably equipment ground.
The Service Bench Surface should be covered with a dissipative material. This can be either an ESD-type high-pressure laminate formed as the benchtop surface, or it may be one of the many types of dissipative mats placed upon the benchtop surface. The mats are available in different colors, with different surface textures, and with various cushioning effects. Whichever type is chosen, look for a material with surface resistivity of 1 x 10⁹ or less, as these materials are sufficiently conductive to discharge objects in less than one second. The ESD laminate or mat must be grounded to the ESD common grounding point to work properly. Frequently, a one Megohm current limiting safety resistor is used in series with the work surface ground. This blog post will provide more information on how to choose and install your ESD working surface.

*Types of Worksurface Matting – click here for more information*

A Dissipative Floor Mat may also be used, especially if the technician intends to wear foot-grounding devices. The selection of the floor mat should take into consideration several factors. If anything is to roll on the mat, then a soft, cushion-type mat will probably not work well. If the tech does a lot of standing, then the soft, anti-fatigue type will be much appreciated. Again, the mat should be grounded to the common ground point, with or without the safety resistor as desired.
Workstation Tools and Supplies should be selected with ESD in mind. Avoid insulators and plastics where possible on and around the bench. Poly bags and normal adhesive tapes can generate substantial charges, as can plastic cups and glasses. If charge-generating plastics and the like cannot be eliminated, consider using one of the small, low cost air ionizers It can usually be mounted off the bench to conserve work area, and then aimed at the area where most of the work is being done. The ionizer does not eliminate the need for grounding the working surface or the operator, but it does drain static charges from insulators, which do not lend themselves to grounding.

Personnel Grounding

People are great static generators. Simple movements at the bench can easily build up charges as high as 500-1000 volts. Therefore, controlling this charge build-up on the technician is essential. The two best known methods for draining the charge on a person are wrist straps with ground cords and foot or heel grounders. Personnel can be grounded through:

Wrist Straps are probably the most common item used for personnel grounding. They are comprised of a conductive band or strap that fits snugly on the wrist. The wrist strap is frequently made of an elastic material with a conductive inner surface, or it may be a metallic expandable band similar to that found on a watch. For more information on wrist straps, check out this post.
Ground Cords are typically made of a highly flexible wire and often are made retractable for additional freedom of movement. There are two safety features that are usually built into the cord, and the user should not attempt to bypass them. The first, and most important, is a current limiting resistor (typically 1 Megohm) which prevents hazardous current from flowing through the cord in the event the wearer inadvertently contacts line voltage. The line voltage may find another path to ground, but the cord is designed to neither increase or reduce shock hazard for voltages under 250 volts. The second safety feature built into most cords is a breakaway connection to allow the user to exit rapidly in an emergency. This is usually accomplished by using a snap connector at the wrist strap end.
Foot or Heel Grounders are frequently used where the technician needs more freedom of movement than the wrist strap and cord allow. The heel grounder is often made of a conductive rubber or vinyl and is worn over a standard shoe. It usually has a strap that passes under the heel for good contact and a strap of some type that is laid inside the shoe for contact to the wearer. Heel grounders must be used with some type of conductive or dissipative floor surface to be effective and should be worn on both feet to insure continuous contact with the floor. Obviously, lifting both feet from the floor while sitting will cause protection to be lost.Don’t forget to regularly check and verify your personnel grounding items:

Summary

An effective static control program doesn’t have to be expensive or complex. The main concept is to minimize generation of static and to drain it away when it does occur, thereby lessening the chance for an ESD event to happen. The ingredients for an effective ESD program are:

Education: to ensure that everyone understands the problem and the proper handling of sensitive devices.
Workstation Grounding: use a dissipative working surface material and dissipative flooring materials as required.
Personnel Grounding: using wrist straps with ground cords and/or foot-grounding devices.
Follow-up to ensure Compliance: all elements of the program should be checked frequently to determine that they are working effectively.

The ESD “threat” is not likely to go away soon, and it is very likely to become an even greater hazard, as electronic devices continue to increase in complexity and decrease in size. By implementing a static control program now, you will be prepared for the more sensitive products that will be coming.

5 Common Mistakes in ESD Control & How to Avoid Them

Image scsstaticcontrol July 26, 2018 1

Many companies implement an ElectroStatic Discharge (ESD) Control Program with the aim of improving their operations. Effective ESD control can be a key to improving:

Productivity
Quality
Customer Satisfaction

Problems arise when an organization invests in ESD protective products and/or equipment and then misuses them. Misuse of ESD protective products and/or equipment wastes invested money and can also be causing more harm than good. Today’s blog post will highlight some of the major issues we have come across and how you can avoid or fix them.

About ESD Control and ESD Protection

Remember that for a successful ESD control program, ESD protection is required throughout the manufacturing process: from goods-in to assembly all the way through to inspection. Anybody who handles electrical or electronic parts, assemblies or equipment that are susceptible to damage by electrostatic discharges should take necessary precautions.

Just like viruses or bacteria that can infect the human body, ESD can be a hidden threat unable to be detected by human eyes. Hidden viral/bacterial threats in hospitals are controlled by extensive contamination control procedures and protective measures such as sterilization. The same principles apply to ESD control: you should never handle, assemble or repair electronic assemblies without taking adequate protective measures against ESD.

Common Mistakes in ESD Control

1. Ionizers are poorly maintained or out-of-balance

If an ionizer is out of balance, instead of neutralizing charges, it will produce primarily positive or negative ions. This results in placing an electrostatic charge on items that are not grounded, potentially discharging and causing ESD damage to nearby sensitive items.

Remember to clean emitter pins and filters using appropriate tools. Create a regular maintenance schedule which will extend the lifespan of your ionizers tremendously.

Consider using ionizers with “Clean Me” and//or “Balance” alarms. These will alert you when maintenance is required.

“All ionization devices will require periodic maintenance for proper operation. Maintenance intervals for ionizers vary widely depending on the type of ionization equipment and use environment. Critical clean room use will generally require more frequent attention. It is important to set up a routine schedule for ionizer service.”

[ESD TR20.20 Handbook Ionization clause 15.8 Maintenance / Cleaning]

If you would like to learn more about how ionizers work and what type of ionizer will work best for your application, check out this post for detailed coverage.

2. ESD Garments are Ungrounded

We’ve seen it so many times: operators wearing an ESD coat (without appropriate wrist straps and/or footwear/flooring) thinking they are properly grounded. However, without proper electrical bonds to a grounding system they are not grounded!

Every ESD garment needs to be electrically bonded to the grounding system of the wearer. Otherwise it just acts as a floating conductor. There are a few options to choose from:

Wrist Straps
ESD footwear/flooring
Hip-to-Cuff grounding

“After verifying that the garment has electrical conductivity through all panels, the garment should be electrically bonded to the grounding system of the wearer so as not to act as a floating conductor.

This can be accomplished by several means:

Ground the garment to the body through a wrist strap-direct connection with an adapter.
Ground the garment through conductive wrist or heel cuffs in direct contact with the skin of a grounded operator.
Ground the garment through a typical separate ground cord, directly attached to an identified groundable point on the garment.
Garments should be worn with the front properly snapped or buttoned to avoid exposure of possible charge on personal clothing worn under the garment.”

[ESD TR20.20 Handbook Garments clause 19.4 Proper Use]

ESD clothing loses their ESD properties over time. It is therefore an important part of the ESD Control Program to incorporate periodic checks (see #3 below) of ESD garments.

If you need more information on ESD garments, we recommend having a look at this post.

3. No Compliance Verification Plan / Not Checking ESD Control Products

Companies can invest thousands of dollars in purchasing and installing ESD control products but then waste their investment by never checking their ESD items. This results in ESD equipment that is out of specification. Without the tools in place to check their ESD items, companies may have no idea if they are actually working correctly. Remember: ESD products (like any other product) are subject to wear and tear, and other errors when workstations get moved, ground cords get disconnected…etc. The list goes on.

When investing in ESD control products, make sure you also establish a Compliance Verification Plan. This ensures that:

ESD equipment is checked periodically
Necessary test equipment is available

“A compliance verification plan shall be established to ensure the organization’s fulfilment of the requirements of the plan. Process monitoring (measurements) shall be conducted in accordance with a compliance verification plan that identifies the technical requirements to be verified, the measurement limits and the frequency at which those verifications shall occur. The compliance verification plan shall document the test methods used for process monitoring and measurements. If the organization uses different test methods to replace those of this standard, the organization shall be able to show that the results achieved correlate with the referenced standards. Where test methods are devised for testing items not covered in this standard, these shall be adequately documented including corresponding test limits. Compliance verification records shall be established and maintained to provide evidence of conformity to the technical requirements.
The test equipment selected shall be capable of making the measurements defined in the compliance verification plan.”[ANSI/ESD clause 7.4 Compliance verification plan]

We provide detailed instructions on how to create a Compliance Verification Plan in this post.

4. Improperly Re-Using Shielding Bags / Using Shielding Bags with Holes or Scratches

ESD Shielding Bags are used to store and transport ESD sensitive items. When used properly, they create a Faraday Cage effect which causes charges to be conducted around the outside surface. Since similar charges repel, charges will rest on the exterior and ESD sensitive items on the inside will be ‘safe’. However, if the shielding layer of an ESD Shielding Bag is damaged, ESD sensitive items on the inside will not be protected anymore.

Re-using shielding bags is acceptable as long as there is no damage to the shielding layer. Shielding bags with holes, tears or excessive wrinkles should be discarded.

Use a system of labels to identify when the bag has gone through five (5) handling cycles. When there are five broken labels, the bag is discarded.

ESD shielding packaging is to be used particularly when transporting or storing ESD sensitive items outside an ESD Protected Area.

“Transportation of ESDS items outside an ESD Protected Area (hereafter referred to as “EPA”) requires enclosure in static protective materials, although the type of material depends on the situation and destination. Inside an EPA, low charging and static dissipative materials may provide adequate protection. Outside an EPA, low charging and static discharge shielding materials are recommended. While these materials are not discussed in

the document, it is important to recognize the differences in their application. For more clarification see ANSI/ESD S541. “

[ANSI/ESD Foreword]

This post provides further “dos and don’ts” when using ESD Shielding Bags.

5. Using Household Cleaners on ESD Matting

The use of standard household cleaners on ESD matting can put an ESD Control Program at risk and damage the ESD properties of items. Many household cleaners contain silicone or other insulative contaminants which create that lovely shine you get when wiping surfaces in your home. The problem is that silicone and other chemical contaminates can create an insulative layer which reduces the grounding performance of the mat.

Don’t spend all this extra money on ESD matting and then coat it with an insulative layer by using household cleaners. There are many specially formulated ESD surface and mat cleaners available on the market. Only clean your ESD working surfaces using those cleaners.

“Periodic cleaning, following the manufacturer’s recommendations, is required to maintain proper electrical function of all work surfaces. Ensure that the cleaning products used to not leave an electrically insulative residue which is common with some household cleaners that contain silicone.”

[ESD TR20.20 Handbook Worksurfaces clause 10.5 Maintenance]

Conclusion

There are many more issues we see when setting foot into EPAs and the above list is by no means complete. These are the most common issues we’ve found when assessing EPAs.

It is important to train all personnel using ESD products and/or equipment to follow proper ESD control programs, and maintenance procedures to avoid common ESD control mistakes. Basic ESD control principles should be followed for an ESD control program to be successful:

Ground conductors.
Remove, convert or neutralize insulators with ionizers.
Shield ESD sensitive items when stored or transported outside the EPA.

What mistakes do you commonly see when walking through an EPA? Let us know what you commonly see in the comments and your solutions for fixing them!

For more information on how to get your ESD control program off the ground and create an EPA, check this post.

Definitions of Resistivity and Resistance in ESD Control

Image scsstaticcontrol August 10, 2017 1

There is a lot of confusion out there as to what the difference is between resistivity and resistance. We get asked questions on a regular basis so hopefully this post will put an end to any misunderstanding – we’ll explain the difference between the two and will point out the measurements you really need to worry about when it comes to your ESD Control Program.

The difference between Resistivity and Resistance
“Resistance or resistivity measurements help define the material’s ability to provide electrostatic shielding or charge dissipation.” [Source]
However, resistance and resistivity values are not interchangeable. Let’s get a bit technical here to illustrate the difference between the two:

The resistance expresses the ability of a material to conduct electricity. It is therefore related to current and voltage. In fact, the surface resistance of a material is the ratio of the voltage and current that’s flowing between two pre-defined electrodes.
With a pure resistive material, where:
– R is the resistance (expressed in Ohm W),
– U is the voltage (expressed in Volt) and
– I is the current (expressed in Amp).The unit of measure for surface resistance is ohms (W). It is important to remember that the surface resistance of a material is dependent on the electrodes used (shape as well as distance). If your company implements an ESD Control Program compliant to the ESD Standard ANSI/ESD S20.20, it is therefore vital to carry out surface resistance measurements as described in the Standard itself.
The surface resistivity of a material describes a general physical property. It is not influenced by the shape of the electrodes used or the distance between them. “Surface resistivity, ρ, can be defined for electric current flowing across a surface as the ratio of DC voltage drop per unit length to the surface current per unit width.” [Dr. Jaakko Paasi, VTT Industrial Systems: “Surface resistance or surface resistivity?”]
As Dr. Jaakko Paasi describes in his research note, surface resistivity can be expressed by using a concentric ring probe as
where:
– k is the geometrical coefficient of the electrode assembly,
– r_centre is the outside radius of the centre electrode and
– r_outer is the inside radius of the outer electrode.For the electrodes recommended by ESD TR53 (Compliance Verification of ESD Protective Equipment and Materials), the coefficient k = 10.The unit of measure for surface resistivity is ohms (W) but in practice you will often see ohms/square (W/square) (which technically is not a physical unit).
As previously explained, the surface resistivity does not depend on shape or distance of the electrodes used when performing the test. You can compare results freely – no matter what type of electrode was used to get the measurements in the first place.

Converting from Resistivity to Resistance
“Values of surface resistance and surface resistivity become comparable if the measured surface resistance value is multiplied by the geometrical coefficient of the used electrode fixture.” [Dr. Jaakko Paasi, VTT Industrial Systems: “Surface resistance or surface resistivity?”]
If you measure surface resistance according to ESD TR53, then the corresponding surface resistivity can be calculated by multiplying the resistance value by the geometrical coefficient factor k = 10. Likewise, surface resistivities can be converted to surface resistances by dividing the surface resistivity value by 10.

Care is needed in interpreting results when measuring non-homogeneous materials such as multilayer mats or conductive-backed synthetic fiber carpeting containing a small amount of conductive fiber. Buried conductive layers can provide shunt paths. Be clear when stating what you have measured!
A few notes in regards to measuring surface resistance and resistivity:

On large surfaces, such as worksurface mats, readings will sometimes vary with increasing time of measurement. This is due to the ‘electrification’ of the mat beyond the area measured. It is therefore important to measure properly and to keep the duration of measurement constant. Fifteen seconds is an arbitrary but practical duration for measurement time.
Moreover, the materials needing to be checked in an EPA are most of the time, non-conductive polymers that have been made conductive or antistatic by addition of conductive particles or by special treatments during manufacture. The resistivity of such materials may vary from one point to another or they may be direction dependent (anisotropic).
ESD TR53 goes some way to specifying the procedures to be followed and test probes to be used, so that the results can be compared, at least roughly.
Also, the resistance of some materials may vary with humidity level and temperature. It is therefore good practice to take a note of these two parameters when measuring.

So now that we’ve identified what the difference is between surface resistance and resistivity, there is one more thing we want to cover in today’s post: the different types of surface resistances you will come across when dealing with ESD and how to measure them:

1. Resistance to Ground (R_g)
“Resistance to Ground is a measurement that indicates the capability of an item to conduct an electrical charge (current flow) to an attached ground connection. The higher the resistance in the path, the more slowly the charge will move though that defined path.” [Source]
The Resistance to Ground is measured to ensure that surfaces in an EPA are correctly grounded. This is certainly one of the most useful measurements in an EPA.

To perform the test:

One 5lb cylindrical probe is required for this measurement.
Connect the probe to a megohmmeter and place it on the surface to test.
Connect the other ohmmeter lead to earth or to an ESD ground point.
Measure the resistance at 10V for conductive items and 100V for dissipative items.

2. Resistance Point-To-Point (R_p-p)
“A point-to-point measurement used during the qualification process evaluates floor and worksurface materials, garments, chair elements, some packaging items, and many other static-control materials.“ [Source]
Resistance Point-To-Point is used to assess the performance of an item used in an EPA.

Performing a Resistance Point-To-Point Test

To perform the test:

Two 5lb cylindrical probes are required for this measurement
Connect the probes to a megohmmeter.
Place the material to be tested on an insulative surface such as clean glass and place the probes on the material.
Measure the resistance at 10V for conductive items and 100V for dissipative items.
Move the probes to measure in a cross direction and repeat the test.

“Point-to-point measurements are important during the qualification process for proper evaluation of flooring and worksurface materials. After installation, the resistance-to-ground measurement is more applicable since it emulates how the material really behaves in practice.” [Source]

3. Volume Resistance (R_V)
Although this is one of the less common measurements when it comes to ESD, it’s still worth to mention the volume resistance here. You would measure the volume resistance when a non-grounded item such as a container is to be placed on a grounded item, such as a mat. The volume resistance will indicate whether the item can be used in the desired manner.

To perform the test:

Two 5lb cylindrical probes are required for this measurement
Connect the probes to a megohm meter.
Put the first probe upside down and ‘sandwich’ the test sample between it and the second probe placed on top.
Measure the resistance.

So hopefully we have put an end to any confusion in regards to surface resistivity and resistance and answered all your questions. If there is anything else you’d like to know, let us know in the comments.

References:

Jaakko Paasi, VTT Industrial Systems: “Surface resistance or surface resistivity?”
David E. Swenson, Affinity Static Control Consulting: “Electrical Resistance and Resistivity”
ESD Association, Inc.: ESD Fundamentals – Part 3: Basic ESD Control Procedures and Materials

The importance of an ESD Protected Area (EPA)

Image scsstaticcontrol May 18, 2017 3

In our last post, we talked about ESD: what it is, what types of ESD damage there are and what costly effects ESD can have. Missed our very first post? Catch-up here.
All caught up? Right, moving on. Today you will learn how to avoid ESD damage and protect your ESD sensitive items. So, let’s jump right in.

The fundamental ESD Control Principles
We’ve established that ESD is the hidden enemy in the electronics industry. Therefore, the BIG question is: how exactly do you control ElectroStatic Discharge (ESD) in your workplace? Easy – just follow these ESD fundamentals:

Ground all conductors including people
Remove all unnecessary non-conductors (also known as insulators)
Place ESD sensitive devices inside of shielding packaging when transported outside of an ESD Protected Area (EPA)

Per ESD Handbook ESD TR20.20-2008 section 2.4 “It should be understood that any object, item, material or person could be a source of static electricity in the work environment. Removal of unnecessary nonconductors, replacing nonconductive materials with dissipative or conductive materials and grounding all conductors are the principle methods of controlling static electricity in the workplace, regardless of the activity.”

These are the essential principles of ESD Control. If you implement all three points above, you will be in control of ESD and your sensitive items will be protected. Well, that wasn’t hard, was it? Don’t be terrified – we’ll go through everything in detail. We’ll cover #2 and #3 in future points – today’s focus is #1.

Definition of an ESD Protected Area (EPA)
An ESD Protected Area (EPA) is a designated zone – all surfaces, objects, people and ESD Sensitive Devices (ESDs) within are kept at the same electrical potential. This is achieved by simply using ‘groundable’ materials for covering of surfaces and for the manufacture of containers and tools. This applies to all items with an electrical resistance of less than 10⁹ ohms.

An EPA could be just one workstation or it could be a room containing several different workstations. It can be portable as used in a field service situation or permanent.

Example-EPA-Area — *Example of an ESD Protected Area*

The user guide CLC/TR 61340-5-2:2008 defines an EPA as follows:
“An ESD protected area (EPA) is an area that is equipped with the ESD control items required to minimize the chance of damaging ESD sensitive devices. In the broad sense, a protected area is capable of controlling static electricity on all items that enter that work area. Personnel and other conductive or dissipative items shall be electrically bonded together and connected to ground (or a common connection point when a ground is not available) to equalize electrical potential among the items. The size of an EPA can vary greatly. A protected area may be a permanent workstation within a room or an entire factory floor encompassing thousands of workstations. A protected area may also be a portable worksurface or mat used in a field service situation.” [CLC/TR 61340-5-2:2008 Use guide clause 4.6 Protected areas (EPA)]

You’re probably wondering now, how exactly you can get all surfaces, objects and operators to the same electrical potential. Fear not – we’ve got you covered!

Personnel Grounding
As previously stated, a fundamental principle of ESD control is to ground conductors including people at ESD protected workstations.Wrist straps are the first line of defense against ESD, the most common personnel grounding device used, and are required to be used if the operator is sitting. The wristband should be worn snug to the skin with its coil cord connected to a common point ground which is connected to ground, preferably equipment ground.

Wearing a wrist strap and connecting it to a common point ground

If you are not using a continuous or a constant monitor, a wrist strap should be tested while being worn at least daily. This quick check can determine that no break in the path-to-ground has occurred. Part of the path-to-ground is the perspiration layer on the person; an operator with dry skin may inhibit the removal of static charges and may cause a test failure.
“The wrist strap system should be tested daily to ensure proper electrical value. Nominally, the upper resistance reading should be ” [ANSI/ESD S1.1 Annex A, 3 Frequency of Functional Testing]

A Flooring / Footwear system is an alternative for personnel grounding for standing or mobile workers. Foot grounders or other types of ESD footwear are worn while standing or walking on an ESD floor. ESD footwear is to be worn on both feet and should be tested independently at least daily while being worn. Unless the tester has a split footplate, each foot should be tested independently, typically with the other foot raised in the air.
“Compliance verification should be performed prior to each use (daily, shift change, etc.). The accumulation of insulative materials may increase the foot grounder system resistance. If foot grounders are worn outside the ESD protected area testing for functionality before reentry to the ESD protected area should be considered.” [ESD SP9.2 APPENDIX B – Foot Grounder Usage Guidance]

Both ESD footwear and ESD floor are required. Wearing ESD footwear on a regular, insulative floor is a waste of time and money.

Wearing foot grounders on an ESD floor

Part of the path-to-ground is the perspiration in the person’s shoes. The conductive tab or ribbon of foot grounders should be placed inside the shoe under the foot with the excess length tucked into the shoe. Thanks to the perspiration in the shoe, direct contact with the skin is normally not necessary.

If an operator leaves the EPA and walks outside wearing ESD footwear, care should be taken not to get the ESD footwear soiled. Dirt is typically insulative, and the best practice is to re-test the ESD footwear while being worn each time when re-entering the EPA.
Working Surfaces
ESD working surfaces, such as mats, are typically an integral part of the ESD workstation, particularly in areas where hand assembly occurs. The purpose of the ESD working surface is two-fold:
1. To provide a surface with little to no charge on it.
2. To provide a surface that will remove ElectroStatic charges from conductors including ESDS devices and assemblies) that are placed on the surface.
ESD mats need to be grounded. A ground wire from the mat should connect to the common point ground which is connected to ground, preferably equipment ground. For electronics manufacturing a working surface resistance to ground (R_G) of 1 x 10⁶ to less than 1 x 10⁹ ohms is recommended.
“The single most important concept in the field of static control is grounding. Attaching all electrically conductive and dissipative items in the workplace to ground allows built-up electrostatic charges to equalize with ground potential. A grounded conductor cannot hold a static charge.” [Grounding ANSI/ESD S6.1 Foreword]
Per ANSI/ESD S20.20 section 6.2.1.2 Grounding / Bonding Systems Guidance, “In most cases, the third wire (green) AC equipment ground is the preferred choice for ground.”
Best practice is that ground connections use firm fitting connecting devices such as metallic crimps, snaps and banana plugs to connect to designated ground points. The use of alligator clips is not recommended.

The working surface must be maintained and should be cleaned with an ESD cleaner. Regular cleaners typically contain silicone, and should never be used on an ESD working surface. ESD Handbook ESD TR20.20-2008 section 5.3.1.14 Maintenance “Periodic cleaning, following the manufacturerís recommendations, is required to maintain proper electrical function of all worksurfaces. Ensure that cleaners that are used do not leave an electrically insulative residue common with some household cleaners that contain silicone.“
Other moveable objects
Moveable items (such as containers and tools) are grounded when placed on a grounded surface or being held by a grounded operator. Everything that does not readily dissipate charge must be excluded from the EPA (refer to #2 of our ESD Control Principles above). Regular plastics, polystyrene foam drink cups and packaging materials, etc. are typically high charging and have no place at an ESD protective workstation.

Intention of an ESD Protected Area (EPA)We’ve learnt in our previous blog post that ElectroStatic discharge (ESD) can damage components and products that contain electronics. A lot of the time, this damage is not detected during quality inspection and can cause significant problems further down the line.An ESD Protected Area (EPA) is an area that has specifically been created to control ESD; its purpose is therefore to avoid ALL problems resulting from ESD damage. Workers need to understand AND follow the basics of ESD control to limit the generation of electrostatic charges as well as limit and slow discharges in the EPA.Recognizing an ESD Protected Area (EPA)
An ESD Protected Area must be clearly identified using signs and/or aisle tape. This ensures operators and visitors are alerted when entering (or leaving) an ESD Protected Area which require special precautions (grounding via wrist straps and/or foot grounders etc.). It also indicates that they are entering (or exiting) areas where exposed ESDS items can be handled safely.Remember to be consistent throughout your shop floor, i.e. use the same signs. This will avoid confusion for your operators.

Example of an EPA caution sign

“While signs are one way of indicating the boundaries of an EPA, it is not the only way. Any alternate method that alert the personnel that an EPA begins is acceptable to ANSI/ESD S20.20. Some of the alternate ways to mark the boundaries of an EPA are:
- tape on the floor
- different color floor tiles
- different color carpet
- any other way to establish boundary conditions
Anyway to distinguish the boundaries of an EPA would be acceptable as long as the personnel are aware of the indications and take the proper precautions while inside the EPA.” [ESD TR20.20-2016 section 9.1.2 EPA Boundary Indicators]

Building an ESD Protected Area (EPA)
A basic form of an ESD Protected Area is a workstation consisting of the following components:
- An ESD working surface mat
- A grounding cord
- A wristband
- A coiled cord
- A common point ground
To set-up an EPA:
1. Connect the ESD working surface mat to the common point ground using the grounding cord.
2. Link the operator to the common point ground using the wristband and coiled cord.
Congratulations – you’ve just created an ESD Protected Area!
By following the above steps, each component (the ESD mat and the operator) is kept at the same electrical potential (ground). Any ElectroStatic charge (ESD) is removed to ground via the common point ground.